Hello, I just purchased an 80 gal and I am now shopping for a skimmer. I would prefer it to be a hang on as I do not plan on running a sump. I plan on keeping mostly lps and zos along with a couple peices of hydnaphora that i currently have in my 37gal. I'm gona be using about 80#s live sand and...
I have a couple items listed on ebay for sale. Get them for your fish this Christmas!
ETSS Super Reef Devil
Eheim 1060 600gph pump
Both items are in great shape; used in my sump for about 6mos. Let me know if you have any questions!
Stuff F/S in Sacramento...NO SHIPPING..!!
cleaning my garage and still have things for sale...email me or pm your number or picture requests...thank you!!
1-55gal TRU VU custom with middle divider and built in corner overflow on both sides..48Lx18Hx18w....300$ new and will sell for .....125$...
The pump on my ETSS Super Reef Devil skimmer died tonight. It stopped pumping earlier, so my wife unplugged it. On three consecutive attempts to replug it, it tripped the GFCI (Thank goodness).
It is a Catalina/Aquarium CA 1800 pump/powerhead (rated @ 8 ft. max. head; [email protected])
Im pretty new to the hobby,so im not sure what is good,and i need peoples opions to make sure im not getting ripped off..This guy is offering me his skimmer its a Precision marine hot-1..for 75$ 4mths old, i looked it up,and its retailed at 160.00,and sites say its pretty good,but i need...
Check out what I tripped over while I was in the garage.
ETSS 800.....yah thats right!:dance:
I'm not sure if I should leave the injector tube as is or retrofit it with a becket injector???
What do you guys think?..........Andy??
Just recently my skimmer has decided to output millions of microbubbles and I can't figure out what is causing it. The skimmer is an ETSS Super Reef Devil being run by a mag 9.5. The pump is actually a little too strong so I have attached a ball valve to scale it down a little. This setup was...
Here's the current set-up:
FOWLR + a few softies.
55 gal tank w/ approx 12 gal in two sumps
ETSS Super Reef Devil Skimmer
60-75 lbs live rock (~8 lbs Figi 4 yrs ago, rest cultured in my tank)
2 NO 40 w bulbs, 1 actinic, 1 10,000K
2 Percula Clowns ~1"
1 Hippo tang ~3"
I have a 4+ year old Gold Stripe Maroon Clown that suddenly showed signs of stress a little while ago. Here is the set-up:
FOWL + 3 new, small (<1") mushrooms, added 2 on Friday, 1 10-days ago.
55 gal tank w/ approx 12 gal in two sumps
ETSS Super Reef Devil Skimmer, working well...
OK, I've now had my new ETSS Super Reef Devil Skimmer for about 6 weeks. It took about a week to start collecting crud and then it would fill the cup within about 4-5 days with a nice thick dark scum. lately it has been filling the cup with mostly water within 12-16 hrs.
My question is this...
Hello, My name is Michael.
This tank has been up for 3 months. It is an All Glass 90gl. w/over flow and tank drain. I am running a Little Giant MDQ2 pump on one loop for circulation, about 740 gph. An ETSS UHF sump with an ETSS Super Reef Devil skimmer. A Cap 1800 runs the skimmer, and a Cap...
Just wondering what the best skimmer in your opinion is for under $200. I have been looking at the Aqua C urchin, and the Red Sea Berlins. Are there any others worth looking at?
It will be running in a 29 gallon sump, with a 46 gallon display.
Ok....I'm to the point where the FUN actually begins.I've recieved all my equipment orders, read A TON of very informative articles on this board and some others,I've done 3 months of research.Now I get to add water!! <IMG SRC="smilies/dance.gif" border="0">
Let me bounce my set up off of you...
Hello. I am still in the preparation phase for a reef tank. At this time, all I have is an Oceanic reef ready 58 g tank and stand.
Regarding a skimmer, if you had to choose for this tank between an ETSS Super Reef Devil, AquaC Urchin Pro, or AquaC EV90, which would you choose? I don't have a...
My berlin skimmer would proudce a good amount of foam in the riser tube but would break back down before entering the collection cup. The problem was because there was only about a 3/16 gap between the lid and the the riser tube which wouldn't let the foam freely escape.
I used a Dremel and...